is seeking certified and qualified DBE subcontractors and/or suppliers to provide Stewart Engineering Inc. is requesting quotes from all qualified subcontractors and suppliers including certified DBE firms for the following items of work, including but not limited to: LEAD COMPLIANCE PLAN LEVEL 2 CRITICAL PATH METHOD SCHEDULE TIME-RELATED OVERHEAD (LS) DISPUTE RESOLUTION ADVISOR ON-SITE MEETING HOURLY OFF-SITE DISPUTE-RESOLUTION-ADVISOR-RELATED TASKS CONSTRUCTION AREA SIGNS TRAFFIC CONTROL SYSTEM STATIONARY IMPACT ATTENUATOR VEHICLE FLASHING ARROW SIGN TYPE III BARRICADE TEMPORARY TRAFFIC STRIPE (TAPE) CHANNELIZER (SURFACE MOUNTED) PORTABLE RADAR SPEED FEEDBACK SIGN SYSTEMS (LS) TEMPORARY BARRIER SYSTEM PORTABLE CHANGEABLE MESSAGE SIGN (LS) ALTERNATIVE TEMPORARY CRASH CUSHION JOB SITE MANAGEMENT PREPARE STORM WATER POLLUTION PREVENTION PLAN RAIN EVENT ACTION PLAN STORM WATER SAMPLING AND ANALYSIS DAY STORM WATER ANNUAL REPORT MOVE-IN/MOVE-OUT (TEMPORARY EROSION CONTROL) TEMPORARY HYDRAULIC MULCH (BONDED FIBER MATRIX) TEMPORARY COVER TEMPORARY CHECK DAM TEMPORARY DRAINAGE INLET PROTECTION TEMPORARY FIBER ROLL TEMPORARY GRAVEL BAG BERM TEMPORARY REINFORCED SILT FENCE TEMPORARY CONSTRUCTION ENTRANCE STREET SWEEPING TEMPORARY CONCRETE WASHOUT CONTRACTOR-SUPPLIED BIOLOGIST (LS) DUST CONTROL PLAN (NATURALLY OCCURRING ASBESTOS) TEMPORARY HIGH-VISIBILITY FENCE CLEARING AND GRUBBING (LS) ROADWAY EXCAVATION (NATURALLY OCCURRING ASBESTOS) SHOULDER BACKING STRUCTURE EXCAVATION (SOLDIER PILE WALL, NATURALLY OCCURRING ASBESTOS) (F) - STRUCTURE BACKFILL (SOLDIER PILE WALL) (F) - CONCRETE BACKFILL (SOLDIER PILE WALL) (F) - LEAN CONCRETE BACKFILL IMPORTED BORROW (CY) HYDROMULCH FIBER ROLLS HYDROSEED COMPOST (CY) CLASS 2 AGGREGATE BASE (CY) HOT MIX ASPHALT (TYPE A) ASPHALT BINDER (GEOSYNTHETIC PAVEMENT INTERLAYER) GEOSYNTHETIC PAVEMENT INTERLAYER (PAVING FABRIC) TACK COAT COLD PLANE ASPHALT CONCRETE PAVEMENT GROUND ANCHOR (SUBHORIZONTAL) STEEL SOLDIER PILE (HP 14 X 89) 30" DRILLED HOLE STRUCTURAL CONCRETE, WALER STRUCTURAL CONCRETE, COPING PRECAST CONCRETE LAGGING (F) - BAR REINFORCING STEEL (WALER) (F) - BAR REINFORCING STEEL (GALVANIZED) BAR REINFORCING STEEL (COPING) CLEAN AND PAINT STEEL SOLDIER PILING 24" CORRUGATED STEEL PIPE (.138" THICK) REMOVE CULVERT (LF) ROCK SLOPE PROTECTION (1/2 T, CLASS VII, METHOD A) (CY) ROCK SLOPE PROTECTION (150 LB, CLASS III, METHOD B) (CY) ROCK SLOPE PROTECTION (20 LB, CLASS I, METHOD B) (CY) ROCK SLOPE PROTECTION FABRIC (CLASS 8) MINOR CONCRETE (GUTTER) (LF) MINOR CONCRETE (GUTTER) (CY) DESTROY WELL 14' PIPE GATE REMOVE PAVEMENT MARKER PAVEMENT MARKER (RETROREFLECTIVE) MARKER (CULVERT) MIDWEST GUARDRAIL SYSTEM (8' STEEL POST) VEGETATION CONTROL (MINOR CONCRETE) (F) - CABLE RAILING END ANCHOR ASSEMBLY (TYPE SFT-M) ALTERNATIVE IN-LINE TERMINAL SYSTEM 6" THERMOPLASTIC TRAFFIC STRIPE (ENHANCED WET NIGHT VISIBILITY) (BROKEN 36-12) 6" THERMOPLASTIC TRAFFIC STRIPE (ENHANCED WET NIGHT VISIBILITY) REMOVE THERMOPLASTIC TRAFFIC STRIPE 12" RUMBLE STRIP (ASPHALT CONCRETE PAVEMENT) MOBILIZATION Stewart Engineering Inc. is an Equal Opportunity Employer and will work with suppliers and subcontractors to identify opportunities and break down items into economically feasible units as reasonably necessary.
Construction on State Highway in In Mendocino County Near Hopland From 0.7 Mile To 1.3 Miles North Of Geysers Road
Contract No. 01-0H8104
State of California Department of Transportation
Route 101 Mile Marker 0.7, Cloverdale, CA, 95425
08-30-2022 at 01:00 PM
Renee Thomas
5302448464
5302448462
P.O. Box 990010, Redding, CA, 96099
PROJECT DETAILS:
Stewart Engineering Inc. is an Equal Opportunity Employer and will work with suppliers and subcontractors to identify opportunities and break down items into economically feasible units as reasonably necessary.
Stewart Engineering Inc. will be bidding the referenced project as a prime contractor. Plans and specifications for this project may be viewed at your local builders exchange and are available for review in our office. If you require additional information regarding the requirements of the contract, please don’t hesitate to contact our office. In order that we may give your bid maximum consideration, please supply us with a fax or email letter prior to the bid describing the scope of your work.
Stewart Engineering is signatory to the Labors Union Local 185 and Operators Union Local 3. We encourage and actively solicit proposals from DBE subcontractors and suppliers on all our projects. All qualified DBE subcontractors must be registered and certified by the California Department of Transportation. Prior to the bid, upon request, you can contact our office if you require assistance in bonding, lines of credit, insurance, obtaining necessary equipment, supplies, materials or services etc., which may be required by the Owner. Subcontractors must possess a current contractor’s license, worker’s compensation and insurance coverage during the entire length of the prime contract. All Subcontractors will be required to sign our standard Subcontract Agreement (AGC Long Form Standard Subcontract). If you require an advance copy to of the subcontract to look over please contact our office. You must be registered and provide your Department of Industrial Relations number
